The pool may no longer be accessible by software that does not support Still be used, but some features are unavailable.Īction: Enable all features using 'zpool upgrade'. Status: Some supported features are not enabled on the pool. Scan: scrub repaired 0 in 0 days 00:01:01 with 0 errors on Fri Feb 7 03:46:01 2020 You should find what you need.Īs for why the server did not came back, it can be because the UPS itself did not or because the server is configured for not to in its BIOS. Do some research around NUT and the upsc command. Because you just suffered a full discharge, wait for your battery to be at 100% before doing a long test. You can do a short test basically anytime. And that one is related with your next question : It is about the same for NUT, the program managing the UPS. In the GUI, you can send you a test e-mail to confirm your config is working. Audible alarms: On battery, low battery, overload, Software: PowerPanel personal edition Management cable: USB cable, LED indicators: power on. Now that your system is back up, it would be a good time to test your e-mail alert config. With RaidZ2, it would be very surprising (almost impossible) for ZFS not to be able to recover if something got corrupted. It will either finish without any error or will fix whatever error may have be caused by the failure. Your pool should be Ok but to have the absolute evidence about it, just do a scrub. You can clear all doubt by doing a scrub. Memory 4x M393B2G70QH0-YK0 Samsung 16GB PC3L-12800R DDR3-1600MHz ECC Registered Server Ram 64GB In the past before I upgraded to 11.3 I would get an email if my server was on UPS batteryġ) Why didn't I get an email? Is that a bug in 11.3Ģ) Why didn't the system shut down before the battery was exhausted (current setting is 900 seconds)?ģ) Why didn't the server come back up so I could reach it thru the VPN? Not sure but I think that it did but I couldn't reach it till I rebooted the pfSense router when I got home because my windows machine wasn't connecting to the internet (DNS error) that was fixed by a reboot of the router when I got home.Ĥ) how can I test my UPS without unplugging it.ĥ) Do I have to worry that my data is not 100% if the server didn't shut down properly? The operating system successfully came back online at Fri Feb 7 15:46:19 2020.įIY I fixed the time on the IPMI interface after seeing the server came backup tomorrow. That program offers hibernate as a shut-down option before the backup battery power is depleted.Power Supply Failure Detected - DeassertedįreenasSuper.local had an unscheduled system reboot. It is detected by macOS natively and I've installed Cyberpower's PowerPanel Personal, which is running fine. The UPS is connected to the Mac mini by USB as it runs 24/7. I cannot believe the company won't fix this-the software seems to be entirely neglected by the CyberPower folks who make it.īut at least they offer an alternative: The free CyberPower PowerPanel Business Edition (I'm running the latest version, 3.23). Following a recent power outage I've purchased a Cyberpower pure sine wave UPS for my networking equipment and an old Intel Mac mini that I use for staging websites. However, I could never get the link to appear on my Windows 10 Enterprise system even though hibernation was enabled in my OS configuration's Power settings (in Control Panel). Note: If hibernation is disabled or not supported, the computer will Recommended that the hibernation should be enabled to avoid the data Hibernation, or click No button not to enable the hibernation. Click the shortcutĪnd then the Confirm Hibernation Enabling message will ask whether toĮnable the hibernation or not. Users to determine whether to enable hibernation. The Enable Hibernation on your computer shortcut will be displayed for If the hibernation is supported and is not enabled on your computer, Well, the PowerPanel Personal Edition online help says this about hibernation: Then you need to choose the Configuration option, which requires Windows Administrator privileges: To enable the options in the application, you have to find the green "P" icon in the system tray and right-click it. This is terrible software design, and the people who wrote it should be required to listen to repeated plays of Disney's "It's a Small World" song in a locked room for one week. How do I test a scheduled shutdown Follow the steps below to test a scheduled shutdown: 1. Why are the items grayed-out and how do you enable them? 1) Why are the items grayed-out and how do you enable them?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |